HP DESIGNJET T1300 SERVICE MANUAL PDF

Manuals or user guides for your HP DesignJet T in Printer. HP DesignJet T and T Printer Series. Using your The only warranties for HP products and services are set .. Web Services manual configuration. Service Manual and more parts for CRA DesignJet t in eprinter.

Author: Megul Maugis
Country: Haiti
Language: English (Spanish)
Genre: History
Published (Last): 24 December 2016
Pages: 187
PDF File Size: 2.35 Mb
ePub File Size: 13.58 Mb
ISBN: 170-4-22269-824-3
Downloads: 81566
Price: Free* [*Free Regsitration Required]
Uploader: Kerisar

All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Hewlett-Packard Company. The information contained in this The procedures described in this manual are The Warning symbol calls attention to a document is subject to change without to be performed by HP-qualified service procedure, practice, or the like, which, notice.

For information about using these products, refer to the corresponding User and Quick Reference Guides. Readership The procedures described in this Service Manual are to be performed by HP Certified service personnel only. Emergency firmware upgrade with USB flash drive Obtaining the product log and the diagnostics package The internal part of the Touch Control Panel is the Home Screen and this is divided into three main areas: Using the Touch Control Panel The front panel is located on the front right of the printer.

It gives you complete control of your printer: This does not discard any changes made in the current screen. Home screen dynamic icons The following items are displayed only on the home screen. With the product turned off, press the Power Key When the magic frame LEDs become active, select by touching one of the following sequences: If you have an error code which is not documented in this Service Manual or you have an error which you cannot resolve, then report the error to the HP Response Center or the nearest HP Support Office.

When reporting the error, have the information ready, refer to Shown below is a list of the Service tests and the component s tested: Check the type of paper that is being used since the Line sensor may have problems detecting transparent paper or some types of Non-HP paper.

Try loading white HP paper in to the product and check that the Line sensor detects it.

Unlatch the CIS Cover. Open the CIS and clear the area of any paper. The basket was damaged during the product setup There are three plastic parts that could break during product installation and need replacing.

HP Service Manual for CRA DesignJet t in eprinter

The paper should load over the roll toward you. For each of the ink t3100 used in the product, there are two components, the Printhead and Ink One thing that users may notice is that Gray ink is used in higher quantities than Cyan, Magenta and Yellow inks. To change an ink cartridge there are two methods, the first is shown below by using the ink tab, the second method is to access the main menu option refer to the User’s Guide for further details.

  AKTA SEWA BELI 1967 PDF

Press on the Information icon. Press on the Ink Menu icon and the following screen is displayed.

DESIGNJET T/T ePrinter series & T eMFP series Service manual

The information supplied is: Changing sfrvice Printhead To change a Printhead there are two methods, the first is shown below by using the printhead tab, the second method is to access the main menu option refer to the User’s Guide for further details. Press on the Printhead Menu icon and the following screen is displayed.

Pull the blue handle up and toward you to release the Carriage Cover. Push the handle back. This gives you access to the printheads.

Remove a printhead by lifting up the blue t13000. Using the blue handle, use steady force to disengage desingjet printhead. Pull the blue handle upward until the printhead is released from the carriage.

Do not pull abruptly because this can damage the printhead. The Touch Control Panel display identifies the missing printhead. To insert a new printhead first remove the orange sevice caps.

Insert the new printhead into its correct slot in the carriage. Insert the printhead slowly and vertically, straight down. It may be damaged if you insert it too fast, or at an angle, or if you rotate it as you insert it. Push down as indicated by the arrow shown below. Insert all other printheads that need to be installed, and close the carriage lid. Ensure t11300 end of the blue handle catches the wire loop on the near side of the carriage.

Lower the handle to rest on the carriage cover. When all the printheads have been inserted correctly and are accepted by the product, the product beeps. The Touch Control Panel display confirms that all printheads are correctly inserted.

The product starts checking and preparing the printheads. The default routine process, when all printheads are changed, takes 10 minutes. If the product finds problems in preparing the printheads, it takes longer, up to 45 minutes.

HP DesignJet T1300 44-in Printer User Guides

Image Quality Maintenance Procedure Load the paper you wish to use. You can designje a roll that is at least mm 24 in wide or a cut sheet that is A2 landscape or larger. Do not use transparent and semi-transparent paper to align the printheads. Test printhead separately You are recommended to test the printheads individually to find the failing printhead.

Remove all the printheads and insert them alone one by one, Closing the latch and the carriage cover after every insertion. The Touch Control Panel display will indicate the failing one showing the reseat or replace message. Ensure that the Ink Cartridge is the correct color for that slot.

Ensure that the Ink Cartridge is the correct orientation, with the color coded label at the top.

Clean the electrical connections on the backside of the printhead with a lint-free cloth. You can carefully use a mild rubbing alcohol if moisture is needed to remove residue. Do not use water. You can use the Flex Contacts Cleaning Tool. This is a delicate process and may damage the printhead.

  LEY AVELINO SIANI 2012 PDF

Whenever you replace the Printhead, check the empty slots to see if they need cleaning. In extreme circumstances, when a Printhead is inserted, it is possible that the product will not recognize it due to the build-up of ink on the electrical connection between the Printhead and the Carriage Assembly. Included with the product is a Flex Contacts Cleaning Tool. Follow the advice given in the appropriate serfice below. Embedded LAN connectivity troubleshooting Perform the following procedure, checking the connectivity carefully after each step to see whether the problem has been fixed.

If any test fails, the printer describes the problem majual recommends how yp solve it. USB device connectivity troubleshooting If possible, try using t11300 different computer. EIO Jetdirect card connectivity troubleshooting Perform the following procedure, checking the connectivity carefully after each step to see whether the problem has been fixed. USB flash drive are supported. Load the firmware onto any empty flash drive mmanual insert the flash drive into one of the USB ports of the product.

When reporting the error, have the following information ready: If you fail to provide any of the following information, HP Support cannot help you properly.

When investigating a system error, you are recommended to use the diagnostic package to further understand the problem. Follow these steps to troubleshoot the issue. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. If however the LEDs stay Panel on, this would indicate t1030 greater problem, light on System Error Codes—Full Descriptions This sections describes each of the system error codes and warnings that could be encountered while using the product and provides the repaperl action required to solve the problem sesignjet.

Replace one component at a time and check whether the error has gone before replacing another component. Check that the Trailing Cable is not damaged. Check the condition and connections of the Interconnect data and power cable, replace if necessary,see Interconnect PCA on page USB Cable not connected Corrective action: A feature on the Touch Control Panel hangs or will not function copy,scan etc Corrective action: Turn off the product and turn on again, and check to see if the error remains.

Upgrade the firmware For more information, see Appendix B: Emergency firmware upgrade with USB flash drive on page Scanner not calibrated Corrective deisgnjet Reboot Product System Error: Contex Library failed to load Corrective action: Reboot the Product Upgrade the firmware For more information, see Power cable of the Scanner is failing Corrective action: Check the condition and connections of the Scanner Power cable, if necessary replace the cable.

Failure moving Service Station Corrective action: Check the Primer Tubes.